Types of modern cement

Portland cement blends

Portland cement blends are often available as inter-ground mixtures from cement producers, but similar formulations are often also mixed from the ground components at the concrete mixing plant.[35] Portland blastfurnace cement contains up to 70% ground granulated blast furnace slag, with the rest Portland clinker and a little gypsum. All compositions produce high ultimate strength, but as slag content is increased, early strength is reduced, while sulfate resistance increases and heat evolution diminishes. Used as an economic alternative to Portland sulfate-resisting and low-heat cements.Portland flyash cement contains up to 35% fly ash. The fly ash is pozzolanic, so that ultimate strength is maintained. Because fly ash addition allows a lower concrete water content, early strength can also be maintained. Where good quality cheap fly ash is available, this can be an economic alternative to ordinary Portland cement Portland pozzolan cement includes fly ash cement, since fly ash is a pozzolan, but also includes cements made from other natural or artificial pozzolans. In countries where volcanic ashes are available (e.g. Italy, Chile, Mexico, the Philippines) these cements are often the most common form in use.. High Temperature Insulation  Portland silica fume cement. Addition of silica fume can yield exceptionally high strengths, and cements containing 5–20% silica fume are occasionally produced.

However, silica fume is more usually added to Portland cement at the concrete mixer. Masonry cements are used for preparing bricklaying mortars and stuccos, and must not be used in concrete. They are usually complex proprietary formulations containing Portland clinker and a number of other ingredients that may include limestone, hydrated lime, air entrainers, retarders, waterproofers and coloring agents. They are formulated to yield workable mortars that allow rapid and consistent masonry work. Subtle variations of Masonry cement in the US are Plastic Cements and Stucco Cements. These are designed to produce controlled bond with masonry blocks. Expansive cements contain, in addition to Portland clinker, expansive clinkers (usually sulfoaluminate clinkers), and are designed to offset the effects of drying shrinkage that is normally encountered with hydraulic cements. This allows large floor slabs (up to 60 m square) to be prepared without contraction joints. White blended cements may be made using white clinker and white supplementary materials such as high-purity metakaolin. Colored cements are used for decorative purposes.
High Temperature Cement

In some standards, the addition of pigments to produce "colored Portland cement" is allowed. In other standards (e.g. ASTM), pigments are not allowed constituents of Portland cement, and colored cements are sold as "blended hydraulic cements". Very finely ground cements are made from mixtures of cement with sand or with slag or other pozzolan type minerals that are extremely finely ground together. Such cements can have the same physical characteristics as normal cement but with 50% less cement particularly due to their increased surface area for the chemical reaction. Even with intensive grinding they can use up to 50% less energy to fabricate than ordinary Portland cements.

New method of growing high-quality graphene promising for next-gen technology

New method of growing high-quality graphene promising for next-gen technology (Nanowerk News) Making waves as the material that will revolutionize electronics, graphene – composed of a single layer of Carbon atoms – has nonetheless been challenging to produce in a way that will be practical for innovative electronics applications. Researchers at UC Santa Barbara have discovered a method to synthesize high quality graphene in a controlled manner that may pave the way for next-generation electronics application.

Kaustav Banerjee, a professor with the Electrical and Computer Engineering department and Director of the Nanoelectronics Research Lab at UCSB that has been studying carbon nanomaterials for more than seven years, led the research team to perfect methods of growing sheets of graphene, as detailed in a study to be published in the November 2011 issue of the journal Carbon.

UCSB researchers have successfully controlled the growth of a high-quality bilayer graphene on a copper substrate using a method called chemical vapor deposition (CVD), which breaks down molecules of methane gas to build graphene sheets with carbon atoms. (Image: Peter Allen) "Our process has certain unique advantages that give rise to high quality graphene," says Banerjee. "For the electronics industry to effectively use graphene, it must first be grown selectively and in larger sheets. We have developed a synthesis technique that yields high- quality and high-uniformity graphene that can be translated into a scalable process for industry applications."

Using adhesive tape to lift flakes of graphene from graphite, University of Manchester researchers Geim and Novoselov were awarded the 2010 Nobel Prize in Physics for their pioneering isolation and characterization of the material. To launch graphene into futuristic applications, however, researchers have been seeking a controlled and efficient way to grow a higher quality of this single-atom-thick material in larger areas.

The discovery by UCSB researchers turns graphene production into an industry-friendly process by improving the quality and uniformity of graphene using efficient and reproducible methods. They were able to control the number of graphene layers produced – from mono-layer to bi-layer graphene – an important distinction for future applications in electronics and other technology.

"Intel has a keen interest in graphene due to many possibilities it holds for the next generation of energy- efficient computing, but there are many roadblocks along the way," added Intel Fellow, Shekhar Borkar. "The scalable synthesis technique developed by Professor Banerjee's group at UCSB is an important step forward."

As a material, graphene is the thinnest and strongest in the world – more than 100 times stronger than diamond – and is capable of acting as an ultimate conductor at room temperature. If it can be produced effectively, graphene's properties make it ideal for advancements in green electronics, super strong materials, and medical technology. Graphene could be used to make flexible screens and electronic devices, computers with 1,000 GHz processors that run on virtually no energy, and ultra-efficient solar power cells. Key to the UCSB team's discovery is their understanding of graphene growth kinetics under the influence of the substrate. Their approach uses a method called low pressure chemical vapor deposition (LPCVD) and involves disintegrating the hydrocarbon gas methane at a specific high temperature to build uniform layers of carbon (as graphene) on a pretreated copper substrate. Banerjee's research group established a set of techniques that optimized the uniformity and quality of graphene, while controlling the number of graphene layers they grew on their substrate.

According to Dr. Wei Liu, a post-doctoral researcher and co-author of the study, "Graphene growth is strongly affected by imperfection sites on the copper substrate. By proper treatment of the copper surface and precise selection of the growth parameters, the quality and uniformity of graphene are significantly improved and the number of graphene layers can be controlled."

Professor Banerjee and credited authors Wei Liu, Hong Li, Chuan Xu and Yasin Khatami are not the first research team to make graphene using the CVD method, but they are the first to successfully refine critical methods to grow a high quality of graphene. In the past, a key challenge for the CVD method has been that it yields a lower quality of graphene in terms of carrier mobility – or how well it conducts electrons. "Our graphene exhibits the highest reported field-effect mobility to date for CVD graphene, having an average value of 4000 cm2/V.s with the highest peak value at 5500 cm2/V.s. This is an extremely high value compared with the mobility of silicon." added Hong Li, a Ph.D. candidate in Banerjee's research group.

"Kaustav Banerjee's group is leading graphene nanoelectronics research efforts at UCSB, from material synthesis to device design and circuit exploration. His work has provided our campus with unique and very powerful capabilities," added David Awschalom, Professor of Physics, Electrical and Computer Engineering, and Director of the California NanoSystems Institute (CNSI) at UCSB where Banerjee's laboratory is located. "This new facility has also boosted our opportunities for collaborations across various science and engineering disciplines."

"There is no doubt graphene is a superior material. Intrinsically it is amazing," says Banerjee. "It is up to us, the scientists and engineers, to show how we can use graphene and harness its capabilities. There are challenges in how to grow it, how to transfer or not to transfer and pattern it, and how to tailor its properties for specific applications. But these challenges are fertile grounds for exciting research in the future."

Mesh

Mesh
       Mesh consists of semi-permeable barrier made of connected strands of metal, fiber, or other flexible/ductile material. Mesh is similar to web or net in that it has many attached or woven strands Types of mesh A plastic mesh is extruded, oriented, expanded or tubular. Plastic mesh can be made from polypropylene, polyethylene, nylon, PVC or PTFE. A metal mesh can be woven, knitted, welded, expanded, photo-chemically etched or electroformed (screen filter) from steel or other metals.In clothing, a mesh is often defined as a loosely woven or knitted fabric that has a large number of closely spaced holes, frequently used for modern sports jerseys and other clothing. A mesh skin graft is a skin patch that has been cut systematically to create a mesh. Meshing of skin grafts provides coverage of a greater surface area at the recipient site, and also allows for the egress of serous or sanguinous fluid. However, it results in a rather pebbled appearance upon healing that may ultimately look less aesthetically pleasing. Uses of meshes Meshes are often used to screen out unwanted things, such as insects. Wire screens on windows and mosquito netting can be considered as types of meshes. Wire screens can be used to shield against radio frequency radiation, e.g. in microwave ovens and Faraday cages. Metal and nylon wire mesh filters are used in filtration Wire mesh is used in guarding for secure areas and as protection in the form of vandal screens. Wire mesh can be fabricated to produce park benches, waste baskets and other baskets for material handling. A huge quantity of mesh is being used for screen printing work. Surgical mesh is used to provide a reinforcing structure in surgical procedures like inguinal hernioplasty, and umbilical hernia repair. Meshes are also used as drum heads in practice and electronic drum sets.

High temperature insulation

High temperature insulation Calcium silicate
    Calcium silicate (often referred to by its shortened trade name Cal-Sil or Calsil) is the chemical compound Ca2SiO4, also known as calcium orthosilicate and sometimes formulated 2CaO.SiO2. It is one of group of compounds obtained by reacting calcium oxide and silica in various ratios[3] e.g. 3CaO•SiO2, Ca3SiO5; 2CaO•SiO2, Ca2SiO4; 3CaO•2SiO2, Ca3Si2O7 and CaO•SiO2, CaSiO3. Calcium orthosilicate is a white powder with a low bulk density and high physical water absorption. It is used as an anti-caking agent and an antacid. A white free-flowing powder derived from limestone and diatomaceous earth, calcium silicate has no known adverse effects to health[citation needed]. It is used in roads, insulation, bricks, roof tiles, table salt[4] and occurs in cements, where it is known as belite (or in cement chemist notation C2S).


High temperature insulation
   Calcium silicate is commonly used as a safe alternative to asbestos for high temperature insulation materials. Industrial grade piping and equipment insulation is often fabricated from calcium silicate. Its fabrication is a routine part of the curriculum for insulation apprentices. Calcium silicate competes in these realms against rockwool as well as proprietary insulation solids, such as perlite mixture and vermiculite bonded with sodium silicate. Although it is popularly considered an asbestos substitute, early uses of calcium silicate for insulation still made use of asbestos fibers.

Synthetic adhesives

Synthetic adhesives
     Synthetic adhesives are based on elastomers, thermoplastics, emulsions, and thermosets. Examples of thermosetting adhesives are: epoxy, polyurethane, cyanoacrylate and acrylic polymers. See also post-it notes. The first commercially produced synthetic adhesive was Karlsons klister in the 1920s.

Aluminium

Aluminium ( /ˌæljuːˈmɪniəm/ al-ew-min-ee-əm) or aluminum (American English;  /əˈluːmɪnəm/ ə-loo-mi-nəm) is a chemical element in the boron group with symbol Al and atomic number 13. It is silvery white, and it is not soluble in water under normal circumstances.
Aluminium is the third most abundant element (after oxygen and silicon), and the most abundant metal, in the Earth's crust. It makes up about 8% by weight of the Earth's solid surface. Aluminium metal is so chemically reactive that native specimens are rare and limited to extreme reducing environments. Instead, it is found combined in over 270 different minerals.[6] The chief ore of aluminium is bauxite.
Aluminium is remarkable for the metal's low density and for its ability to resist corrosion due to the phenomenon of passivation. Structural components made from aluminium and its alloys are vital to the aerospace industry and are important in other areas of transportation and structural materials. The most useful compounds of aluminium, at least on a weight basis, are the oxides and sulfates.
Despite its prevalence in the environment, aluminium salts are not known to be used by any form of life. In keeping with its pervasiveness, aluminium is well tolerated by plants and animals.[7] Owing to their prevalence, potential beneficial (or otherwise) biological roles of aluminium

Pressure-sensitive adhesive

          Pressure sensitive adhesive (PSA, self adhesive, self stick adhesive) is adhesive which forms bond when pressure is applied to marry the adhesive with the adherend. No solvent, water, or heat is needed to activate the adhesive. It is used in pressure sensitive tapes, labels, note pads, automobile trim, and a wide variety of other products.

          As the name "pressure sensitive" indicates, the degree of bond is influenced by the amount of pressure which is used to apply the adhesive to the surface.

          Surface factors such as smoothness, surface energy, removal of contaminants, etc. are also important to proper bonding.

          PSAs are usually designed to form a bond and hold properly at room temperatures. PSAs typically reduce or lose their tack at low temperatures and reduce their shear holding ability at high temperatures; special adhesives are made to function at high or low temperatures. It is important to choose an adhesive formulation which is designed for its intended use conditions.

Thank for Info : http://en.wikipedia.org

Refractory metals

          Refractory metals are a class of metals that are extraordinarily resistant to heat and wear. The expression is mostly used in the context of materials science, metallurgy and engineering. The definition of which elements belong to this group differs. The most common definition includes five elements: two of the fifth period (niobium andmolybdenum) and three of the sixth period (tantalum, tungsten, and rhenium). They all share some properties, including a melting point above 2000 °C and high hardness at room temperature. They are chemically inert and have a relatively high density. Their high melting points make powder metallurgy the method of choice for fabricatingcomponents from these metals. Some of their applications include tools to work metals at high temperatures, wire filaments, casting molds, and chemical reaction vessels in corrosive environments. Partly due to the high melting point, refractory metals are stable against creep deformation to very high temperatures.


Thank for Info : http://en.wikipedia.org

Oil shale

Oil shale

          Oil shale, also known as kerogen shale, is an organic-rich fine-grained sedimentary rock containing kerogen (a solid mixture of organic chemical compounds) from which liquid hydrocarbons called shale oil (not to be confused with tight oil—crude oil occurring naturally in shales) can be produced. Shale oil is a substitute for conventional crude oil; however, extracting shale oil from oil shale is more costly than the production of conventional crude oil both financially and in terms of its environmental impact. Deposits of oil shale occur around the world, including major deposits in the United States of America. Estimates of global deposits range from 2.8 to 3.3 trillion barrels (450×10⁹ to 520×10⁹ m³) of recoverable oil.

          Heating oil shale to a sufficiently high temperature causes the chemical process of pyrolysis to yield a vapor. Upon cooling the vapor, the liquid shale oil—an unconventional oil—is separated from combustible oil-shale gas (the term shale gas can also refer to gas occurring naturally in shales). Oil shale can also be burnt directly in furnaces as a low-grade fuel for power generation and district heating or used as a raw material in chemical and construction-materials processing.

          Oil shale gains attention as a potential abundant source of oil whenever the price of crude oil rises. At the same time, oil-shale mining and processing raise a number of environmental concerns, such as land use, waste disposal, water use, waste-water management, greenhouse-gas emissions and air pollution. Estonia and China have well-established oil shale industries, and Brazil, Germany, Russia also utilize oil shale.

          Oil shales differ from oil-bearing shales, shale deposits which contain petroleum (tight oil) that is sometimes produced from drilled wells. Examples of oil-bearing shales are the Bakken Formation, Pierre Shale, Niobrara Formation, and Eagle Ford Formation.

Thank for Info : http://en.wikipedia.org

Thermal insulation

Thermal insulation

          Thermal insulation is the reduction of heat transfer between objects in thermal contact or in range of radiative influence. Heat transfer is the transfer of thermal energy between objects of differing temperature. The means to stem heat flow may be especially engineered methods or processes, as well as suitable static objects and materials.

Heat flow is an inevitable consequence of contact between objects of differing temperature. Thermal insulation provides a means to maintain a gradient of temperature, by providing a region of insulation in which heat flow is reduced or thermal radiation is reflected rather than absorbed.

          In building construction, insulating materials are assigned a quantitative measure of the insulating capability, called the R-value.

         In thermal engineering of insulating systems for ovens, reactors, and furnaces, thermal conductivity (K), product density and specific heat (C) are the key product characteristics, which influence insulating efficiency, such as acolodet insulating.

Low thermal conductivity (K) is analogous to high insulating capability (R).

          Aerogels, microporous silica and ceramic fiber insulation are three best performing insulators for applications between 200 Celsius and 2000 Celsius. Zirconia fibers have the lowest thermal conductivity of all ceramic fiber products and are used in applications up to 2000 Celsius.

Thank for Info : http://en.wikipedia.org

Filtration

Filtration

         Filtration is commonly the mechanical or physical operation which is used for the separation of solids from fluids (liquids or gases) by interposing a medium through which only the fluid can pass. Oversize solids in the fluid are retained, but the separation is not complete; solids will be contaminated with some fluid and filtrate will contain fine particles (depending on the pore size and filter thickness). Filtration is also used to describe some biological processes, especially in water treatment and sewage treatment in which undesirable constituents are removed by absorption into a biological film grown on or in the filter medium.


Thank for Info : http://en.wikipedia.org

REFRACTORY CASTABLES

REFRACTORY CASTABLES

Refractory castables can be used to create the monolithic linings within all types of furnaces and kilns. They can be further classified into the following sub-categories: conventional, low iron, low cement, and insulating for installation either by gunning or manually. There is a wide variety of raw materials that refractory castables are derived from, including chamotte, andalusite, bauxite, mullite, corundum, tabular alumina, silicon carbide, and both perlite and vermiculite can be used for insulation purposes.

CONVENTIONAL DENSE CASTABLES

Conventional dense castables are created with high alumina cement, and can withstand temperatures from 1300^oC to 1800^oC. These refractory castables are great for common furnace applications, burner blocks, speciality muffle furnaces and oiler work. Resistance is a key quality that varies with the choice of materials, resulting in abrasion, thermal shock and slag attack. Casting and gunning techniques are the method of installing the materials. For the ease of castable placement, gunning materials and water are combined together at the gunning equipment’s nozzle. This is a great method of placement for bulk materials, in cases when circumstances make formwork overly time consuming or simply impractical. In general, the method of installation will depend on cost and accessibility.

INSULATING CASTABLES

Another product that we supply is the Refractory castables that are low density. These insulating castables pose very low thermal conductivity and are utilized for either high temperature face work or when used for a backup lining, which is found behind dense castables or brick work. Here, the insulating castables are able to decrease the lining’s overall density or the cold face temperature. Their strength, which ranges from low to medium, is based on the fact that their density is low and is the main reason that they are not resistant to abrasion. They are most suitable where they do not have to stand up to much wear and tear.

LOW CEMENT CASTABLES

This type of refractory castable is prepared with a lower amount of cement than the standard dense castable is normally created with. Low cement castable refractories fluctuate in alumina content, which provides exceptional physical properties, including low porosity, great abrasion properties and high vigour. These products will commonly necessitate installation that is controlled, however, the big advantage of low cement castables is that they are easily pumped into position, and some may not require vibration, because they are free flowing.

Thank Infomation From : http://www.vitcas.com/

REFRACTORY CASTABLES

REFRACTORY CASTABLES

Refractory castables can be used to create the monolithic linings within all types of furnaces and kilns. They can be further classified into the following sub-categories: conventional, low iron, low cement, and insulating for installation either by gunning or manually. There is a wide variety of raw materials that refractory castables are derived from, including chamotte, andalusite, bauxite, mullite, corundum, tabular alumina, silicon carbide, and both perlite and vermiculite can be used for insulation purposes.

CONVENTIONAL DENSE CASTABLES

Conventional dense castables are created with high alumina cement, and can withstand temperatures from 1300^oC to 1800^oC. These refractory castables are great for common furnace applications, burner blocks, speciality muffle furnaces and oiler work. Resistance is a key quality that varies with the choice of materials, resulting in abrasion, thermal shock and slag attack. Casting and gunning techniques are the method of installing the materials. For the ease of castable placement, gunning materials and water are combined together at the gunning equipment’s nozzle. This is a great method of placement for bulk materials, in cases when circumstances make formwork overly time consuming or simply impractical. In general, the method of installation will depend on cost and accessibility.

INSULATING CASTABLES

Another product that we supply is the Refractory castables that are low density. These insulating castables pose very low thermal conductivity and are utilized for either high temperature face work or when used for a backup lining, which is found behind dense castables or brick work. Here, the insulating castables are able to decrease the lining’s overall density or the cold face temperature. Their strength, which ranges from low to medium, is based on the fact that their density is low and is the main reason that they are not resistant to abrasion. They are most suitable where they do not have to stand up to much wear and tear.

LOW CEMENT CASTABLES

This type of refractory castable is prepared with a lower amount of cement than the standard dense castable is normally created with. Low cement castable refractories fluctuate in alumina content, which provides exceptional physical properties, including low porosity, great abrasion properties and high vigour. These products will commonly necessitate installation that is controlled, however, the big advantage of low cement castables is that they are easily pumped into position, and some may not require vibration, because they are free flowing.

Refractory Castable

คอนกรีตทนไฟ (อังกฤษ: Refractory Castable) เป็นวัสดุทนไฟประเภทหนึ่ง ที่มีลักษณะและวิธีการใช้งานคล้ายกับคอนกรีตที่ใช้ในงานก่อสร้าง แต่เนื้อวัสดุที่นำมาใช้ผลิตเป็นคอนกรีตทนไฟ จะเป็น Refractory Material ซึ่งรวมถึง เม็ดวัตถุดิบหยาบ (Aggregate) และ สารประสาน (Binder) ซึ่งมักจะเป็น High Alumina Cement

[แก้]ประเภทของคอนกรีตทนไฟ

คอนกรีตทนไฟ สามารถแบ่งเป็นประเภทได้โดยเกณฑ์ที่แตกต่างกัน เช่น

1.แบ่งตามปริมาณ แคลเซียมออกไซด์ (CaO) ที่เป็นองค์ประกอบในเนื้อผลิตภัณฑ์ ได้ดังนี้

1.Conventional Castable เป็นคอนกรีตทนไฟ ที่มีปริมาณองค์ประกอบ CaO อยู่ในปริมาณสูง กว่า 2%

2. Low Cement Castable เป็นคอนกรีตทนไฟ ที่มีปริมาณองค์ประกอบ CaO อยู่ในกระมาณต่ำกว่า 2%

3. Cementless Castable เป็นคอนกรีตทนไฟ ที่มีปริมาณองค์ประกอบ CaO ต่ำกว่า 0.2%

แบ่งตามลักษณะในการติดตั้ง

1. Vibrating Castable คอนกรีตทนไฟ ที่ติดตั้ง โดยการหล่อแบบ โดยใช้การเขย่าช่วย

2. Self flow Casatble คอนกรีตทนไฟ ที่ติดตั้ง โดยการหล่อแบบ โดยใช้การ

3. Gunning Material คอนกรีตทนไฟ ที่ติดตั้ง โดยการใช้เครื่องยิง

1. Wet Gunning Material คอนกรีตทนไฟ ที่ติดตั้งโดยใช้เครื่องยิง โดยต้องทำการผสมกับน้ำให้เข้ากันก่อนนำไปติดตั้งโดยใช้เครื่องยิง

2. Dry Gunning Material คอนกรีตทนไฟ ที่ติดตั้งโดยใช้เครื่องยิง โดยไม่ต้องผสมกับน้ำก่อนนำไปใช้งาน

ผลิตภัณฑ์จะมีลักษณะเป็นผงแห้ง จะถูกบรรจุเข้าในเครื่องยิง แล้วจะถูกอัดด้วยแรงดันลม ไปตามท่อยาง จนถึงหัวยิง (Nozzle)โดยจะมีจุดเชื่อมต่อกับท่อน้ำที่ปลายท่อยิง ผลิตภัณฑ์จะผสมกับน้ำที่ ปลายท่อยิง ก่อนจะถูกยิงออกไป

Refractory Castable

คอนกรีตทนไฟ (อังกฤษ: Refractory Castable) เป็นวัสดุทนไฟประเภทหนึ่ง ที่มีลักษณะและวิธีการใช้งานคล้ายกับคอนกรีตที่ใช้ในงานก่อสร้าง แต่เนื้อวัสดุที่นำมาใช้ผลิตเป็นคอนกรีตทนไฟ จะเป็น Refractory Material ซึ่งรวมถึง เม็ดวัตถุดิบหยาบ (Aggregate) และ สารประสาน (Binder) ซึ่งมักจะเป็น High Alumina Cement

[แก้]ประเภทของคอนกรีตทนไฟ

คอนกรีตทนไฟ สามารถแบ่งเป็นประเภทได้โดยเกณฑ์ที่แตกต่างกัน เช่น

1.แบ่งตามปริมาณ แคลเซียมออกไซด์ (CaO) ที่เป็นองค์ประกอบในเนื้อผลิตภัณฑ์ ได้ดังนี้

1.Conventional Castable เป็นคอนกรีตทนไฟ ที่มีปริมาณองค์ประกอบ CaO อยู่ในปริมาณสูง กว่า 2%

2. Low Cement Castable เป็นคอนกรีตทนไฟ ที่มีปริมาณองค์ประกอบ CaO อยู่ในกระมาณต่ำกว่า 2%

3. Cementless Castable เป็นคอนกรีตทนไฟ ที่มีปริมาณองค์ประกอบ CaO ต่ำกว่า 0.2%

แบ่งตามลักษณะในการติดตั้ง

1. Vibrating Castable คอนกรีตทนไฟ ที่ติดตั้ง โดยการหล่อแบบ โดยใช้การเขย่าช่วย

2. Self flow Casatble คอนกรีตทนไฟ ที่ติดตั้ง โดยการหล่อแบบ โดยใช้การ

3. Gunning Material คอนกรีตทนไฟ ที่ติดตั้ง โดยการใช้เครื่องยิง

1. Wet Gunning Material คอนกรีตทนไฟ ที่ติดตั้งโดยใช้เครื่องยิง โดยต้องทำการผสมกับน้ำให้เข้ากันก่อนนำไปติดตั้งโดยใช้เครื่องยิง

2. Dry Gunning Material คอนกรีตทนไฟ ที่ติดตั้งโดยใช้เครื่องยิง โดยไม่ต้องผสมกับน้ำก่อนนำไปใช้งาน

ผลิตภัณฑ์จะมีลักษณะเป็นผงแห้ง จะถูกบรรจุเข้าในเครื่องยิง แล้วจะถูกอัดด้วยแรงดันลม ไปตามท่อยาง จนถึงหัวยิง (Nozzle)โดยจะมีจุดเชื่อมต่อกับท่อน้ำที่ปลายท่อยิง ผลิตภัณฑ์จะผสมกับน้ำที่ ปลายท่อยิง ก่อนจะถูกยิงออกไป

Reractory Castable

Product Category : Material Handling Components

Reractory Castable Top & Bottom Blocks is used to hold the induction coil tightly in middle of the tilting furnace box with help of vertical tie rods. Thermafield Power Components Private Limited manufactures Reractory Castable Top & Bottom Blocks. Thermafield Power Components Private Limited supplies different types of induction furnace insulating materials, coil supports and non asbestose sheets, induction furnace hydraulic spares, carbon free hoses, hydraulic cylinders, he plates, duraline induction melting furnace assembly etc. Reractory Castable Top & Bottom Blocks is made from mixture of refractory material, S.S. Reinforcement and certain percentage of water to make the cast formation in fabricated mould. This Reractory Castable Top & Bottom Blocks give the base support to hold the coil and keep in shape while tilting of the furnace.

Salient features of Reractory Castable Top & Bottom Blocks are:

-Durable

-Fire resistant

-Heat resistant

-Chemical resistant

-High strength

-Flame retardant

Reractory Castable

Product Category : Material Handling Components

Reractory Castable Top & Bottom Blocks is used to hold the induction coil tightly in middle of the tilting furnace box with help of vertical tie rods. Thermafield Power Components Private Limited manufactures Reractory Castable Top & Bottom Blocks. Thermafield Power Components Private Limited supplies different types of induction furnace insulating materials, coil supports and non asbestose sheets, induction furnace hydraulic spares, carbon free hoses, hydraulic cylinders, he plates, duraline induction melting furnace assembly etc. Reractory Castable Top & Bottom Blocks is made from mixture of refractory material, S.S. Reinforcement and certain percentage of water to make the cast formation in fabricated mould. This Reractory Castable Top & Bottom Blocks give the base support to hold the coil and keep in shape while tilting of the furnace.

Salient features of Reractory Castable Top & Bottom Blocks are:

-Durable

-Fire resistant

-Heat resistant

-Chemical resistant

-High strength

-Flame retardant